Memorex Dvd Universal Remote Codes

With the DVD Universal Remote ready to “> we will operate our DVD and these remote controls able to manage the audio and also the video devices which are associated with your DVD of any brand. to control any of your DVD devices you would like to enter some specific digit numbers like 2, 3, 4, or 5 digit device code into your DVD universal tv remote. If you can’t ready to find your remote model number you’ve got to see inside the battery compartment or it’d be back of the remote.

We have three methods to program a DVD universal remote together with your devices by using the precise DVD codes for DVD universal remote. So follow the below steps if you have already got the three-digit or four-digit or the five-digit universal DVD remote codes

Memorex DVD Universal Remote 4 Digit Codes

  • 2003, 2424, 0722, 1297, 3349

Memorex DVD Universal Remote 5 Digit Codes

  • 31270, 32213, 20695, 20831, 21270, 30695, 30831

RCA Universal Remote Codes for Memorex DVD players

  • 3391, 3384

One-For-All Universal Remote Codes for Memorex DVD players

  • 0797, 0854

GE Universal Remote Codes for Memorex DVD players

  • 0446, 0394

Philips Universal Remote Codes for Memorex DVD players

  • 1413, 1913, 0246, 1606

There are three simple ways to line up or to configure a universal remote and therefore the first one is employing a Keycode, Programming Via universal remote code for DVD Search, and Manual Setup.

1) Keycode

By using the keycode we will easily program a DVD universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Universal DVD Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal DVD Remote Code

If you couldn’t find the key code which works for the device at that point you’ll set up your DVD universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” which means it’s been saved correctly
  • Now you’re “TV Volume Up” button has been saved to the Universal remote and you’ll use the volume button.

We have a listing of all known and dealing remote codes which will work with Memorex DVD players. The remote codes for Memorex DVD are 4 and 5 digit remote codes. The remote codes will work with all universal remote controls when programmed using the remote user’s manual. The Memorex DVD codes also will work for SAT and CABLE remotes. If you’ve got any issues with the Memorex DVD remote codes not working, leave your question below with the model number of remote and Memorex DVD.

 

Craig TV’s Universal Remote Codes and Program Instructions

Are you looking forward to getting the Craig tv universal remote codes, then here is that the end to your searching, from this blog post we are getting to mention all the universal remote codes for Craig’s soundbar, so why late just check the below list and there you’ll get all kinds of codes like 2 digits, three-digit and also four-digit, five-digit codes too.

We also are providing some methods to program your favorite universal remote with this Craig tv, after finding the steps to program then use the codes to enter to the program as per the methods. allow us to check the procedure too. You’ll program your cable or satellite universal remote to also control your Craig TV. Find for your provider and remote within the list below and enter the TV code provided into the remote. Ask your cable or satellite provider for instructions.

Craig TV’s Universal Remote 4 Digit Codes List

  • 00073, 6222, 06222, 10180, 0073, 10073, 16222, 11822

Universal Remote For Craig Soundbar

  • 00161

Craig TV’s Universal Remote 3 Digit Codes List

  • 541, 536, 691, 662, 666, 667, 682, 009, 657, 669, 694, 532, 542, 533, 963, 038, 042, 053, 037, 161, 180, 282, 171, 064, 038, 064, 009

Craig TV’s Universal Remote 5 Digit Codes List

  • 10180, 13423, 10161, 19411, 11922

By using the keycode we will easily program a Craig universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Craig TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Craig Remote Code

If you couldn’t find the key code which works for the device at that point you’ll found out your Craig universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

We hope the above methods and therefore the codes are worked to program your Craig tv and also for your favorite remote.

Conclusion:

First of all, you’ve got to verify the name of your remote then try all the universal remote codes which are mentioned within the above list one by one, you’ll use the methods to program your remote too, so why late start with any code until you get paired together with your Craig tv.

Devant TV’s Universal Remote Codes and Program Instructions

To use any of your favorite universal remote for your devant tv, you would like to program with the universal remote codes. The codes have mentioned within the below lines and you’ll enter those codes in your device as per the below-mentioned steps. So try those codes like two-digit codes, three, four, and also five-digit codes.

Devant TV’s Universal Remote 3 Digit Codes List

  • 024
    023

Devant TV’s Universal Remote 4 Digit Codes List

  • 0102, 0134, 0193, 0195, 0196, 0214, 0231, 0338, 0349, 0355, 0384, 0416, 0456, 0457, 0460, 0472, 0476, 0477, 0509, 0526

Devant TV’s Universal Remote 5 Digit Codes List

  • 00001
    00002

Here are remote codes to use together with your Devant TV. Program Your Cable or Satellite remote to figure together with your Devant TV. you’ll program your cable or satellite universal remote to also control your Devant TV. ask your cable or satellite provider for instructions.

1) Keycode

By using the keycode we will easily program a Devant universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Devant TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Devant Remote Code

If you couldn’t find the key code which works for the device at that point you’ll set up your Devant universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • We hope the above methods and therefore the codes are worked to program your Devant tv and also for your favorite remote.

Conclusion:

If your device still not programmed with the universal remote, then be happy to ask us your issue as a question and our experts will solve it as soon as possible, many thanks for visiting our blog, keep visiting our official site to urge updates whenever we post new articles.

Goldstar Tv’s Universal Remote Codes and Program Instructions

If you’re using the Goldstar tv then you would like to use the below gold star tv universal remote codes, these codes are often programmed together with your tv and can work perfectly. So why late just check the codes one by one and be programmed together with your tv and universal remote and therefore the codes are often used with all universal remotes if your remote needs a 4 digit code.

Goldstar Tv’s Universal Remote Codes For RCA

  • 027, 172, 1124, 1155, 005, 018, 155, 077, 10178, 003, 1089, 1123, 1207, 012, 1065, 1083, 004, 1093, 1118, 156, 058, 1046, 1078, 196, 008, 1156, 1196, 1005, 006, 1082, 057, 050, 037, 1058, 1025, 1057, 056, 1056, 1009, 1014, 011, 082, 019, 1004, 0178, 089, 1006, 094, 1172, 1117, 1019, 0030, 1171, 1012, 1205, 171, 1013

Goldstar Tv’s Universal Remote 4 Digit Codes List

  • 0037, 0178, 0556, 0714, 0361, 0109, 0606, 0715, 0009, 0370, 0163, 0455, 0004, 0005, 0227, 0338, 0012, 0057, 0080, 0156, 0001, 0251, 0611, 0761, 0931, 1181, 1221, 1501, 1911, 4731, 0030, 0178, 0019, 0056, 1041, 1042, 1043, 1046, 1047, 1049, 1290, 1314, 1359, 1442, 1004, 1005, 1011, 1018, 1050, 1061, 1090, 1091, 1097, 1098, 1400, 1401, 1006, 1012, 1019, 1056, 1057, 1058, 1082, 1155, 1156, 1171, 1172, 1196, 0002, 0502, 0102, 0324, 0435, 0802, 0307, 0609, 0217, 5005, 5006, 5010, 5011, 5013, 5014, 5018, 5020, 5052, 5106, 5151, 5152, 5155, 5197, 5213, 5264, 5309, 5316, 1089, 1093, 1009, 1013, 1014, 1025, 1065, 1078, 1083, 1117, 1118, 1123, 1124, 1205, 1207

Goldstar Tv’s Universal Remote 3 Digit Codes List

  • 505, 526, 523, 545, 546, 566, 573, 652, 654, 627, 722, 520, 506, 655, 653, 564, 658, 702, 718, 720, 656, 219, 588, 693, 004, 005, 009, 012, 056, 057, 080, 133, 155, 156, 172, 227, 338, 006, 019, 058, 171, 082, 196, 060, 001, 002, 030, 032, 039, 106, 178, 037, 377, 042, 043, 109, 072, 003, 011, 027, 050, 008, 018, 077, 089, 094

Goldstar Tv’s Universal Remote 5 Digit Codes List

  • 10178, 10030, 10002, 10019, 1032, 10001, 10032, 10039, 10056, 10409, 11926, 11032, 10005, 12501, 16105, 12210, 17342, 17608, 19307, 11818, 15010, 19114, 12248, 12268, 12269, 12270, 12271, 12284

 

Use the subsequent directions to program your VIZIO Universal remote to use together with your GOLDSTAR TV/VCR Combos device.

  • Manually activate your TV (or device you would like to control)
  • Press the TV (or device) button and hold for five seconds until the LED flashes twice. LED will remain lit.
  • Enter one among the programming codes from the list 0227 0338 for your GOLDSTAR TV/VCR Combos device. Enter it using the amount Buttons. The LED flashes once after entering each digit. If the code is accepted, the LED flashes twice after the last digit is then turned off.
  • Point the VIZIO remote at the device and press the ability button. If the device powers off, setup is complete. If not, repeat steps with a special code.

1) Keycode

By using the keycode we will easily program a Goldstar tv with any of your favorite universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Goldstar TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Goldstar Remote Code

If you couldn’t find the key code which works for the device at that point you’ll set up your Goldstar universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

We hope the above methods and therefore the codes are worked to program your Goldstar tv and also for your favorite remote.

Conclusion:

We have mentioned all the methods and also all the universal remote codes, just you would like to enter the code as per the above-mentioned methods and therefore the device is going to be programmed with the remote.

 

Westinghouse Universal Remote Codes and Program Instructions

Have you purchased the universal remote for your Westinghouse tv and are you confused to program your tv remote along with your favorite Universal remote then you must have the codes, Once you find the step-by-step instructions to program the remote to figure along with your Westinghouse TV, use the remote codes included on this page.

If you’ve got recently bought a universal remote and you would like the remote codes to work your Westinghouse TV, we’ve codes below for your TV that are working. These codes will work with all universal remote controls. If the primary doesn’t work keep trying the numbers down the list.

Westinghouse Universal Remote Codes For Vizio Tv

  • 0143
    0002
    0114
    1146

GE Universal Remote Codes For Westinghouse TV

  • 0143
    0114

RCA Universal Remote Codes For Westinghouse TV

  • 11282, 13382, 2293, 0885, 12397, 1712, 3470, 10451, 10885, 1036, 11217, 0451, 11300, 0463, 10889, 11712, 13094, 072, 1577, 2397, 1217, 13470, 1282, 12293, 10463, 13579, 0890, 3094, 13949, 13559, 3382, 3559, 13899, 11577, 0889

Magnavox Universal Remote Codes For Westinghouse TV

  • 0127
    0112
    0049
    0046

Philips Universal Remote Codes For Westinghouse TV

  • 0915, 0013

First, try these Westinghouse codes

  • 0027, 0478, 0912, 0916

Westinghouse Universal 4 Digit Remote Codes

  • 4797, 3411, 1300, 1712, 0143, 0114, 1146, 3241, 3251, 0111, 1901, 2281, 3711, 3851, 5781, 5971, 5981, 1891, 2141, 0885, 0889, 0890, 1282, 1577, 0451, 1217, 1019, 1027, 1195, 1196, 1336, 1414, 1430, 1433, 1367, 1489, 1454, 0002, 0915, 0013, 1216, 5001, 5054, 5115, 5117, 5237, 5379, 1036

Westinghouse Universal 3 Digit Remote Codes

  • 795, 528, 500, 553, 562, 505, 738, 574, 798, 809, 531, 551, 516, 794, 513, 652, 575, 766, 697, 003, 797, 068, 097, 107, 856, 072

Westinghouse Universal 5 Digit Remote Codes

  • 11712, 13579, 13382, 10885, 11300, 13949, 12293, 13094, 13470, 10890, 11282, 12397, 13908, 10451, 10463, 11217, 10000, 10889, 11577, 12499, 12195, 17133, 19016, 18535, 11106, 12824, 12438, 12536

 

Check them now and program your device remote together with your favorite universal remote then watch your favorite tv show’s and also the other program by simply operating with this universal remote.

How to Program Westinghouse TV Universal Remote?

  • From your tv remote Press and Hold “Mute & Select” options simultaneously until “Two Blinks
  • Now Enter “9,9,1” code and await “Two Blinks
  • Now “Enter 1
  • Then press and release “Volume +” button
  • Point the remote “before the tv” and keep it up pressing and releasing the “CH +” key, whenever the quantity changes
  • Now “Press the Select” choice to lock the code.

1) Keycode

By using the keycode we will easily program a JVC universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “JVC TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal JVC Remote Code

If you couldn’t find the key code which works for the device at that time you’ll found out your JVC universal remote to look mode for the proper one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the amount button.

This is the only way to program a remote to work with Westinghouse models. See the particular device instructions for an appropriate sequence of keystrokes. Learning remote controls are ready to capture commands from Westinghouse remote controls. Some are limited to one command and others can group commands together.

Ocosmo Universal Remote Codes and Program Instructions

If you’d wish to program your ocosmo tv along with your favorite universal remote then you must use the below-mentioned codes either three-digit or four-digit or five-digit codes and then your tv is going to be paired with the universal remote.

You can check the codes which are mentioned below if you couldn’t connect your tv together with your favorite universal remote by using anybody of these codes then try and check the other codes from the below list then finally at one point your remote is going to be programmed.

Ocosmo Universal Remote 5 Digit Codes

  • 13899, 10810, 10000, 11360, 10878, 11599, 10889

Ocosmo TV Remote Code Spectrum

  • 01877, 03560, 01376, 02187, 03294, 05651

Use the below methods to program your ocosmo tv remote together with your |along with your”> together with your favorite universal remote and therefore the codes are mentioned within the above list so use those codes while trying to program your favorite remote with your tv remote.

1) Keycode

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Ocosmo TV’s Device Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat a similar procedure with the various code from a similar a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll found out your universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some overtime but it’s vital to seek out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the ultimate method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • With the above three methods, we will easily Program Our Ocosmo TV’s Device Universal Remote.

Conclusion:

This article is going to be helpful for each universal remote no matter your brand, just you would like to stay on checking the codes until your device programmed together with your favorite universal remote.

 

Soniq Universal Remote Codes and Program Instructions

For your soniq tv we’ve universal remote codes for any sorts of universal remote controls. If you’d wish to soniq tv pairing code then you want to try the below codes then you’ll be using the universal remote for your soniq tv.

Soniq Universal Remote 4 Digit Codes

  • 1473, 0178, 0180, 0003, 0092, 0045, 0019, 0030, 0056, 0032, 0047, 0054, 0060, 0039

Soniq Universal Remote 3 Digit Code

  • 014

Soniq Universal Remote 5 Digit Code

  • 19253

Audiosonic Universal Remote Code For Soniq tv

  • 0301

Skandia Universal Remote Code For Soniq

  • 2551, 2791

If you would like to pair your soniq tv remote together with your favorite universal remote then you must know the procedure to enter the code you’ve got to see the below methods.

1) Keycode

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Soniq TV’s Device Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat an equivalent procedure with the various code from an equivalent a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll set up your universal remote to look mode for the right one. Its a code in manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some overtime but it’s vital to seek out your key code. Once you’ve got done the above procedure your remote should be working for all the in functions.

3) Manual Setup

If the above two methods can’t be helped to you then the ultimate method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • With the above three methods, we will easily Program Our Soniq TV’s Device Universal Remote.

This is the best platform to urge your favorite universal’s remote codes and therefore the codes were mentioned below, you’ve got to do them one by one until your remote is going to be paired together with your favorite universal remote.

 

Durabrand TV Universal Remote Codes and Program Instructions

Do you need Universal Remote Codes? To regulate your Durabrand tv! here you’ll get all kinds of codes like three-digit codes and also four and five too, you would possibly be using any sorts of branded universal remotes and therefore the codes vary from one branded remote to other branded remote control.

You no got to worry about the codes which aren’t supporting your remote, just keep it up changing the codes if the code doesn’t support your remote while trying to program together with your durabrand tv remote.

Durabrand TV Universal Remote 3 Digit Codes

  • 632, 623, 695, 220, 221, 533, 834, 627, 733, 843, 569, 527, 529, 726, 541, 841, 559, 846, 564, 720, 587, 694, 233, 566, 682, 718, 056

Durabrand TV Codes For Directv Remote

  • 10171
    10178

Durabrand TV Universal Remote 4 Digit Codes

  • 0037, 0556, 1652, 1037, 0714, 0178, 1437, 1779, 0171, 1665, 0189, 0135, 0153, 0217, 0157, 1135, 0371, 0861, 0921, 1381, 2271, 2291, 5121, 0141, 0463, 0180, 1034, 1035, 1041, 1044, 1334, 1337, 1353, 1380, 1259, 1481, 1483, 1484, 1506, 0133, 0254, 0458, 1004, 1038, 0520, 0115, 0916, 0323, 0317, 1115, 5002, 5006, 5038, 5041, 5055, 5120, 5253, 5262, 5290, 5307, 5370, 1153, 1167, 1207

Durabrand TV Universal Remote 5 Digit Codes

  • 10463, 10171, 11570, 11665, 10180, 11034, 10178, 10003, 11463, 11595, 13700, 14760, 19209, 18601, 13811, 12726, 12922, 11258, 12258

By using the below above codes we will sync remote to durabrand tv and therefore the methods to program your tv remote is mentioned below, look at now.

1) Keycode

By using the keycode we will easily program a Durabrand universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Durabrand TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Durabrand Remote Code

If you couldn’t find the key code which works for the device at that point you’ll set up your Durabrand universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

If you are trying any of these methods, you’ll find an acceptable method for your branded universal remote to the program, Then you’ll operate your favorite tv programs together with your favorite remote.

Conclusion:

We hope this text was helpful to you, if you couldn’t find codes for your universal remote, then leave a comment which incorporates your remote what type is it and what digit codes did you are trying from those codes.

 

Aiwa TV’s Universal Remote Codes and Program Instructions

To control your Aiwa tv remote with the universal remote you would like to line up your favorite universal remote by using the codes which we’ve mentioned below. If the remote codes seem to be not working then try other codes that are next to those codes.

To found out your tv remote together with your favorite universal remote you must have their codes either three-digit or four-digit or regardless of the digits which work better and also the setup procedure. All the codes are mentioned below and also the procedures too, check them from the below lines one by one.

Aiwa TV’s Universal Remote 3 Digit Codes

  • 751, 667, 590, 572, 018, 195, 196, 227, 269, 032, 036

Aiwa TV’s Universal Remote 4 Digit Codes

  • 3512, 1505, 0701, 1916, 1908, 0705, 0195, 0196, 0227, 0269, 0411, 0651, 0931, 1411, 4731, 4801, 1155, 1164, 1488, 1512, 1034, 1036, 0121, 0221, 0324, 0528, 5011, 5295, 5296, 5309, 1032, 1236

Aiwa TV’s Universal Remote 5 Digit Codes

  • 11362, 10701, 11914, 10032, 11916, 17342, 14102, 16507, 19307, 14118, 18041, 12248, 12270

We have mentioned four methods to line up your Aiwa remote together with your favorite universal remote, you would like to induce the code from the above list and enter that code as like we said within the below procedures.

This is the primary method you must try it once and it definitely works otherwise you’ll try the regular methods that are mentioned below.

  • You need to stay on Press And Hold the “Clear TV button” until all the “Four Lights Illuminate
  • Here you’ve got to “Select The Code
  • Now press the “Pound” button for just 1 time
  • You need to press the “Red Power Button” and release whenever your “TV Turns Off

1) Keycode

By using the keycode we will easily program an Aiwa universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Aiwa TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Aiwa Remote Code

If you couldn’t find the key code which works for the device at that point you’ll set up your Aiwa universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

Conclusion:

Once you program your tv remote with the universal remote by using the above codes, then you’ll no get to worry about the setup procedure just use and luxuriate in the tv programs.

 

Xenon TV Universal Remote Codes and Program Instructions

To operate any device which features a universal remote, we must need their codes either they could be three-digit, four-digit or they could be five-digit codes. From this article, we are giving the most trending codes which are applicable for any branded remote controls.

Through this blog, you’ll skill to program your tv remote with the universal remote by using the below codes and also the steps which we’ve mentioned below. Try the below codes until you discover the working code for your favorite remote.

Xenon TV Universal Remote Codes List

  • 0381
    0389
    039
    036
    00183
    00264

There are various methods to program your universal remote to work your Xenon tv, the methods are mentioned below, just go with the code and enter that code with the assistance of the below methods.

  • You have to “Switch On Your TV
  • Simultaneously hit and hold “TV and SEL” up to three seconds and therefore the button will “Light
  • Now you’ve got to point the remote therewith button lit then enter the codes “3 or 4 or 5” digit codes
  • Now you would like to verify with “Pressing the Volume+” button then automatically the tv volume will increase.
  • Finally, click on the “TV button” then the code (3 or 4 or 5) digit codes are going to be saved.
  • You can get to understand that the codes are saved when the button “blinks twice

1) Keycode

By using the keycode we will easily program a Xenon Tv’s universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Aiwa TV Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Aiwa Remote Code

If you couldn’t find the key code which works for the device at that point you’ll found out your Aiwa universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now you’re “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

Conclusion:

With the above methods, you’ll sync your tv with the universal remote by using the three, four, or five-digit codes too. You’ll use the codes with any universal remote like Comcast, Dish Network, Direct TV, RCA then on.