Pilot Universal Remote Codes and Program Instructions

If you’re using the pilot tv and checking out the pilot universal remote codes then this is often the simplest platform to urge all brands of remote codes for Pilot tv. we’ve mentioned three methods formula to line up your tv remote with the universal remote.

The codes like two-digit, three-digit, and also four-digit codes have mentioned within the below-mentioned table, so type them in your remote and program your favorite TV with a universal remote. If you discover any of these codes couldn’t program your remote then attempt to enter another code from them.

Pilot TV Universal 4 Digit Remote Codes

  • 1367, 0002, 1004, 1061, 0078, 5021, 1043, 1097, 0739, 1359, 1196, 1047, 3434, 1089, 1041, 1093, 5010, 5013, 0706, 0057, 5015, 1025, 5020, 0712, 0556, 0039, 0004, 0087, 0037, 1709, 1078, 1442, 1046, 5006, 0019, 0001, 5151, 0030, 0205, 0733, 1171, 1123

Pilot TV Universal 3 Digit Remote Codes

  • 525, 004, 703, 729, 289, 377, 427, 460, 926

Pilot TV Universal 5 Digit Remote Codes

  • 10019
    10005
    10039
    10030
    12284

There are three simple ways to set up or to configure a universal remote and therefore the first one is employing a Keycode, Programming Via universal remote code for Pilot Search and Manual Setup.

1) Keycode

By using the keycode we will easily program a Pilot universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Universal Pilot Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Pilot Remote Code

If you couldn’t find the key code which works for the device at that point you’ll found out your Pilot universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

If you already know the code for your device, you’ll program it into your remote manually. If you are doing not know the code, you’ll use the code search function to program the remote. This remote may be a great solution to anyone affected by bad eyesight, disappearing remotes, and other people with just too many devices to regulate. Scroll down for Remote Codes. we’ve mentioned three methods formula to line up your tv remote with the universal remote.

Roku TV Universal Remote Codes and Program Instructions

If you’ve got recently bought a universal remote or want to use your cable remote and you would like the remote codes to work your ROKU TV, we’ve remote codes below for your TV that ought to be working. you’ll program your cable or satellite universal remote to regulate your Roku TV. Find your cable provider below and use those remote codes to regulate your ROKU TV.

Roku TV Universal Remote Codes List

  ProvidersCodes for TCL Roku TVs
Altice USA1111, 0821, 0001, 3411, 3311, 2801, 4141, 1931, 1661, 1561
ATT U-verse  1346
Bright House Cable  387,1756
Buckeye Broadband 12434, 2434
Cable One  2434 
Cablevision / Optimum  031
CenturyLink 2414, 2434, 3183
Charter1  11756
Comcast2  11756, 12434, 12290, 12292
Cox Communications  1756, 11756, 12434
DIRECTV  11756
DISH Network  1756, 535, 645
Frontier Communications 688
GE Universal Remote  2891
Model 24922
General Communications 0031, 0107, 0164, 0004, 0009, 0044, 0054, 0000, 0342, 0003, 0125, 0015, 0022, 0052, 0087
Google Fiber 2856
Hawaiian Telcom 2434
Inteset INT-422  10885
Logitech Harmony
Microsoft Xbox One  T1756
ONN  3851
RCA/Voxx  12434,387, 12049
Time Warner  387, 1566, 268
TiVo  0091,0366
Verizon FIOS  180
Windstream 2414, 2434, 3183
WOW!
XFINITY  11756

RCA Universal Remote Codes For Roku

  • 387, 11756, 10818, 12434, 12049

GE Universal Remote Codes For Roku

  • 2891, 0000, 0164, 0107, 0031, 0044, 0022, 0342, 0052, 0015, 0009, 0004, 0125, 0087, 0003, 0054

Philips Universal Remote Codes For Roku

  • 6381, 6251, 2407, 6171, 5931, 6001

ONN Roku TV Universal Remote Codes

  • 3851
    3201

Magnavox Universal Remote Codes For Roku TV

  • 0269
    0270

Dish Remote Codes For TCL Roku TV

  • 1756, 535, 645, 535, 556

Comcast xr2 Remote Code For TCL TV

  • 11756, 11602, 12434, 12290, 12292

DirecTV Universal Remote Codes For Roku TV

  • 11756
    10818

ATT Uverse Model Number: S10-S1 Remote Codes For ROKU TV

  • 1346
    1097

Bright House Cable Model Number: URC1056 Remote Codes For ROKU TV

  • 1756
    0818

Cablevision Model Number: UR2-CBL-CV04 Remote Codes For ROKU TV

  • 031
    081

Charter Model Number: UR4U–MDVR–CHD2 Remote Codes For ROKU TV

  • 11756
    11602

Cox Communications Model Number: URC-8820-MOTO Remote Codes For ROKU TV

  • 1756
    2360

Time Warner Model Number: UR5U-8780L Remote Codes For ROKU TV

  • 387
    251

TIVO Remote Codes For ROKU TV

  • 0091
    0366
    0999

Verizon FIOS Model Number: VZ P265v3 RC Remote Codes For ROKU TV

  • 180
    342

There are three simple ways to set up or to configure a universal remote and therefore the first one is using a Keycode, Programming Via universal remote code for Roku Tv Search, and Manual Setup.

1) Keycode

By using the keycode we will easily program a Roku Tv universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Universal Roku Tv Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

2) Programming Via Universal Roku Tv Remote Code

If you couldn’t find the key code which works for the device at that point you’ll found out your Roku Tv universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

3) Manual Setup

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.

To control your Roku Tv together with your cable, satellite, or universal remote find the code corresponds to your device or component. we’ve provided the programming instructions for every remote next to the codes.

As the Roku Tv has some Roku specific functions that aren’t available on universal remotes. Most universal remotes support Power, volume, Input select. Some expanded universal remotes support additional functions like back, home, up, down, right, left, replay, options, play/pause, reverse scan, and forward scan.

Conclusion:

We hope the above mentioned universal remote codes and also the methods which we’ve mentioned to program your device together with your favorite universal remote. Still, your remote hasn’t been programmed? Then change the code and follow the above steps until your tv programmed with the universal remote, regardless of what quite branded remote you’re using just enter the codes until it works.

Sceptre TV’s Universal Remote Codes and Program Instructions

If you’ve got recently bought a universal remote and you would like the remote codes to work your Sceptre TV, we’ve codes below for your TV that ought to be working. These codes will work with all universal remote controls. If the primary doesn’t work keep trying the numbers down the list.

Sceptre TV’s 4 Digit Universal Remote Codes

  • 0991
    0000
    0080

if these 3 codes not work try below once

  • 2337, 3899, 4886, 2528, 4139, 0149, 1132, 3521, 4071, 5111, 0878, 1217, 1360, 1599, 2506, 1392, 1467, 1365, 1167, 1318, 1814, 0516, 5260, 5367

Sceptre TV’s 3 Digit Universal Remote Codes

  • 500, 677, 781, 640, 654, 159, 246, 207, 674, 908, 641, 837, 552, 064, 279, 086

GE Universal Remote Codes For Sceptre TV

  • 1167, 1132, 0149, 5260, 5367, 3521, 4071, 5111, 3521, 4071, 5111, 3521, 4071, 5111

RCA Universal Remote Codes For Sceptre TV

  • 11217, 1360, 3899, 12528, 0878, 12506, 1599, 11599, 11360, 13899, 2528, 12337, 1217, 2337, 14139, 2506

Setup Instructions

  1. Set the “Mode Switch” to TV.
  2. Press and hold the “Mute” button and therefore the “Select” button until the visible LED blinks twice.
  3. Enter the 5 digit code

To program a Universal or TV remote: See the links below and find the brand and model of your remote control. You’ll also check the remote programming instructions included within the packaging of your remote or find a YouTube video for your specific model number remotely.

Once you discover the step-by-step instructions to program the remote to figure together with your Sceptre TV, use the remote codes included on this page.

You can program the remote to regulate your TV and audio equipment. Spectrum Guide will plan to detect the brand of your TV and rehearse programming the remote to regulate your TV. If your TV brand isn’t detected, or if you favor, you’ll rehearse Programming and Setup below to program the remote.

The Spectrum 1060BC3 remote is preprogrammed to work the Spectrum receiver (cable box) issued to you, an RCA TV, a Toshiba DVD player, and a Pioneer audio receiver.

To program your remote to a device:

  • Turn on a tool and insert the acceptable video media, (DVD, Blu-ray, etc.), if applicable.
  • Locate the corresponding 5-digit programming code for your device. See “Device Codes – Top Brands” below or ask the remote manual.
  • On the remote, press a tool key once (i.e. AUX, DVD, TV, CBL, or STB).
  • Press and hold SETUP until the chosen mode key blinks twice.
  • Enter a 5-digit code listed for your device. the chosen mode key will blink twice.
  • If the chosen mode key emits an extended blink, repeat steps 3-5 and check out entering an equivalent code again.

If you own a combo device like a TV/DVD or TV/VCR:

  • For a TV/DVD combo, activate the unit and insert a DVD. (For a TV/VCR combo, insert a videocassette).
  • Using the remote, press DVD once. Then press and hold SETUP until the DVD key blinks twice.
  • Locate the brand and enter the primary five-digit code. If entered correctly, the DVD key will blink twice.
  • If the DVD key didn’t blink twice after entering the code’s last digit, repeat steps 2-3.
  • Aim the remote at your combo device and press POWER once. The device should close up. If not, then repeat steps 2-3 until you discover a code that works.

If you’ve located a setup code that works for your combo device and a separate TV code is additionally listed, then program this code into the remote to regulate the quantity.

Aim the remote at the device and press Power (or Play) once. The device should close up. If the device doesn’t close up, repeat steps 2-5, until you discover a code that works. If it still doesn’t respond, ask the Troubleshooting section.

Upstar TV’s Universal Remote Codes and Program Instructions

We recently bought a universal remote for an additional bedroom and needed to seek out the remote codes to regulate our existing Sanyo TV and Toshiba DVD player. We ended up searching multiple websites and still didn’t find the code list we would have liked.

So we used multiple sources and gathered up the universal remote 3 digit codes for many TV, VCR, Satellite, DVD, DVR, and Blu-ray players. We compiled this universal remote programming code list to form it easy to seek out the code you would like to regulate your audio and television equipment. We estimate that we’ve 90% of the entire three-digit codes needed to program your universal remote. We created this code list to be easy to use and easy to seek out the code you would like.

Upstar TV’s Universal Remote 4 Digit Codes

  • 4182
    1651
    4405

Upstar TV’s Universal Remote 3 Digit Codes

  • 627
    505
    502
    506
    773

Upstar TV’s Universal Remote 5 Digit Codes

  • 14182
    14405

IP control: MyURemote is an iPhone/iPad/android Universal Remote ready to control many ‘smart’ devices with unmatched support for IP control. Controlling devices directly via IP control requires that MyURemote and your component can communicate over your Wi-Fi network. A key advantage of IP controllable devices is usually that they supply additional feedback. MyURemote supports all main brand IP controllable devices.

Serial control: is enabled by a MyURemote Certified Adapter like the worldwide Caché GC100, iTach flex, IP2SL, or WF2SL. If needed supported the target device, the configuration of interface settings like baud should be performed via the iTach web interface before usage. A key advantage of serial controllable devices is that they supply additional feedback.

IR control: Support for infrared devices is enabled by the interior Android IR blaster or by a MyURemote Certified Adapter like the worldwide Caché GC100, iTach flex, IP2IR, or WF2IR.

You can have your Shaw Direct remote other devices, like your TV, with the subsequent methods:

First method:

  • Download this file and look for your TV brand. write the corresponding codes.
  • Ensure the TV is powered on.
  • On the highest of your remote, press, and hold the TV button until the others (AUX, SAT) flash a minimum of 3 to 4 times.
  • Press within the 5-digit code that you simply noted down.
  • Press the facility button.
  • If the TV turns off, you’ve got successfully programmed your remote with the TV.
  • Press the facility button to show it back on.
  • If not, repeat steps 2-3 using different codes given for your brand of the TV.

Second method:

  • Ensure the TV is powered on.
  • Press and hold the TV button until the others (AUX, SAT) flash a minimum of 3 to 4 times.
  • Press 9, 9, 1. The TV button should flash twice.
  • Press the CH+ button once per second until the TV turns off.
  • Press the OK/ENTER button.
  • Press the facility button to show the TV back on.
  • Test the quantity and/or Power to ascertain if the TV responds to the remote’s commands.

Devices are added to the MyURemote database almost daily, so this list isn’t always up so far. If after reviewing the list of devices you can’t find what you’re trying to find, or you’re still uncertain whether a tool is controllable, please contact MyURemote’s support team for further assistance.

Emerson Universal Remote Codes and Program Instructions

For Emerson device also we will get the Universal Remote in various brands and therefore the codes for this Emerson device are mentioned within the below list you’ll find the Emerson universal remote codes from that list.

Emerson TV Remote 4 Digit Codes

  • 0205
    3031
    3203
    3005
    3010
    3013
    3012
    0181
    0198
    0207
    0490
    3204
    3186
    3015
    3218
    3025
    0650
    0263
    3011
    3008

Emerson TV Remote 2 Digit Codes

  • 01, 03, 04, 23, 32, 34, 35, 77, 83, 84

RCA Universal Remote Codes For Emerson TV

  • 1004 , 1006 , 1012 , 1023 , 1024 , 1025 , 1026 , 1027 ,1028 , 1029 , 1030 , 1031 , 1032 , 1033 , 1034 , 1035 , 1036 , 1037 , 1038 ,1039 , 1041 , 1042 , 1043 , 1044 , 1046 , 1047 , 1048 , 1049 , 1073 , 1123 , 1124 , 1162 , 1171 , 1177 , 1179 , 1191 , 1196 , 1208

Philips Universal Remote Codes For Emerson TV

  • 0002, 0502, 0006, 0115, 0506, 0706, 0520, 0906, 0316, 0505, 0614, 0324, 0924, 0626, 0826, 0027, 0327, 0128, 0228, 0632, 0134, 0247, 0605, 0705, 0805, 0703, 0903, 0004, 0519, 0106, 0104, 0304, 0604, 0804, 0005, 0105, 0305

If you discover any of these codes doesn’t work to program your Emerson device you would like to use another code and you would like to repeat this process until your device has been programmed with the universal remote and therefore the methods to program your device with remote has mentioned below.

1) Keycode

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Emerson Device Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat an equivalent procedure with the various code from an equivalent a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll set up your universal remote to look mode for the right one. Its a code within the manual that forces the remote into the search mode.

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some overtime but it’s vital to seek out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the ultimate method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • With the above three methods we will easily Program Our Emerson Device Universal Remote.

Let us know with what code your device has been programmed together with your favorite universal remote brand. If you didn’t find any code for your remote allow us to know through the comment section we’ll update it as soon as possible.

RCA 4 Device Universal Remote Codes and Program Instructions

Your remote should make your life easier, but if you’ve got a special remote for each device you own, things can quickly become confusing. You would possibly even have different remotes for various parts of a similar TV. During this case, many of us prefer to program an RCA universal remote to regulate all their TVs, set-top boxes, and amplifiers.

RCA 4 Device Universal Remote Codes List

BrandCodes
Admiral10463
Affinity1371713577
Akai10765
AOC11589, 11365, 12014,12087
Apex Digital1239710765
Ario12397
Atvio13636
Audiovox11865, 11564
Auria12087, 12014
Aventura10171
Broksonic10463, 11892
Celera10765
Changhong10765
Coby13478, 13627
Commercial Solutions11447
Contex14053
Curtis13577, 12855, 12466, 12352, 12397, 13636, 13382, 14035
Curtis Mathes11661
Daewoo11661
Disney11892, 11665
Dumont10017
Durabrand10463, 10171, 11665, 10178
Dynex12049, 12184
Electrohome10463, 11670
Electron12855
Elektra10017, 11661
Element13559, 11687, 12183, 12964, 11886, 12256
Emerson11864, 11394, 10171, 10463, 11963, 11886, 10178,11661, 11665, 13623, 12183, 13559
Envision11589, 11365, 12087, 12014
EQD12014, 12087
EQD Auria12014, 12087
ESA10171, 11963
Favi13382
Fluid12964
Funai10171, 11394, 11963, 11864
Gateway11756
GE11447, 10178, 10765
General Electric11447, 10178, 10765
GFM10171, 11963, 11665, 11886, 11864
Gibralter10017
GoldStar10178
Haier11749, 12309, 13382
Hallmark10178
Hannspree11348
Hisense13519, 12183, 13382
Hitachi11643, 11145
iLo11665, 11394
Insignia12049, 11564, 11423, 11892,10171, 10463, 11963, 12184
Inteq10017
iSymphony13382, 13118, 13094
JC Penney10178, 10156
JCM12256
JVC11774, 11601, 12271, 12321, 13650, 11670, 10463, 11892
KDS11687
KLH10765
Kolin11240
Legend12397, 12309
LG12731, 11423, 12358, 12424, 10178, 10017
LXI10156, 10178, 10017
MAG11687
Magnavox12372, 13623, 11866, 11454, 11963, 10171, 11365, 11867
Marantz11454
Matsushita10250
Megatron10178
Memorex11670, 10463, 10178, 11892, 11665, 11927
MGA10178
Midland10017
Mitsubishi11250, 10178
NAD10156, 10178
Naxa12104, 13382
Nexus Electronics12183
Nikko10178, 10017, 10156
Norcent11365, 11589
Olevia11610, 11240
Optimus10250, 11927
Orion10463, 11892, 13540, 13650
Panasonic11480, 11291, 10250, 11927, 10156, 10178
PARK12104
Penney10178, 10156
Philco10171, 11665, 11963, 11394
Philips11867, 12372, 11866, 11454, 10017, 13623, 10171, 11365, 11394
Pioneer11457
Planar11589
Polaroid11523, 14035, 11687, 10765
Portland11661
Prima11749
Proscan11447, 12256, 12183, 13577,13382, 13332, 13717, 13636
Proton10178
Proview11687
Pulsar10017
Quasar10250, 11291, 11927
RadioShack10178
RCA12746, 11447, 12434, 12932, 12247, 13577, 11781, 12187, 13382, 11661, 13717, 12183, 12855, 13332, 13636, 14214
Realistic10178
Runco10017
Samsung12051
Sansui10463, 11892, 13540, 11670, 13564, 14053, 10171, 13559
Sanyo11142, 13488
Sceptre13899, 12528, 12337
Scotch10178
Scott10178
Sears10156, 10171, 10178
Seiki13953, 12964, 13559, 10178
Sens11865
Sharp12360
Sony10810, 11300
Soundesign10178
Spectroniq11687
Squareview10171
SunBriteTV12337, 11610, 12528
Supersonic12104
SVA11963
Sylvania11864, 11886, 10171, 11963, 11394, 11665
Symphonic10171, 11963, 11394
Syntax11610, 11240
Tatung11756
TCL12434, 13183
Technics10250, 10017
TMK10178
TNCi10017
Toshiba11524, 10156, 11656, 12724
TruTech11665
TVS10463
Venturer11865
Vidtech10178
Viewsonic12014, 12745, 12087, 12049, 11564, 11365
Viore12352, 13382, 13118, 12104, 13094
VIZIO11758, 13758, 12707, 12757, 13415, 12512, 11756
Wards10178, 10017, 10156
Waycon10156
Westinghouse11712, 13579, 13382, 11300, 13949,13094, 13470, 12397, 10463
White Westinghouse11661, 10463
Wyse11365
Xiahua11749
Xoceco11749
Xogego11749
Zenith10017, 10178, 11145, 11423,11661, 12731, 11365, 12358, 10463

A step-by-step guide

The first thing you’re getting to want to try to do is to form sure your new remote has batteries in it and therefore the components and devices you would like to be synced are all attached just how you would like them. All set? Now, it’s time to link the remote to the hardware. Here’s what you would like to do:

  • Turn on the component or device you would like to line up.
  • Press and release the button that corresponds with the component that you simply are programming. for instance, if you would like the remote to regulate your TV or Blu-ray player, hit and release the TV button or Blu-ray button. The remote’s On/Off button will illuminate and will remain lit.
  • Now, simultaneously press and hold the Component button and therefore the On/Off button. The illuminated On/Off button will close up. After a flash, it should turn back on.
  • Release both buttons after the On/Off button relights. It should remain on.
  • Now, press and release the Play button on the remote. If the component that you simply are programming doesn’t close up after 5 seconds, still hit the play button every 5 seconds until the component turns off.
  • Next, press and release the Reverse button. Wait to ascertain if the component turns back on, and press it every 3 seconds until it does.
  • Press and release the Stop button to save lots of the programming for the device within the remote’s memory.
  • Repeat steps 1-7 for every additional device you would like to pair together with your remote.

If you don’t press the buttons correctly, you would possibly ruin the syncing process. This is often the most reason why it’d take some trial and error to urge the remote found out. Struggling? Just reboot the hardware, pull the batteries out of the remote, and pop them back in again, then start from the first step.

RCA’s remotes are great if you’re trying to find something simple and functional, but sometimes you’re searching for something more — something which will act because of the total command center for your smart home. If that sounds more your speed, inspect our list of the simplest universal remotes.

RCA’s remotes are great if you’re trying to find something simple and functional, but sometimes you’re searching for something more — something which will act because of the total command center for your smart home. If that sounds more your speed, inspect our list of the simplest universal remotes.

 

To use this universal remote together with your home entertainment the system, first, you would like to program it to regulate your devices. There are four ways you’ll program the universal remote to work your devices. Try them within the order listed here:

  • The Brand Code Search searches through the codes for select brands of devices.
  • The Direct Code Entry allows you to enter a code from the accompanying code list for your brand of device.
  • The Auto Code Search goes automatically through all the codes for the device you’re trying to regulate
  • The Manual Code Search allows you to manually undergo all the codes for the device you’re trying to regulate.

RCA’s remotes are great if you’re trying to find something simple and functional, but sometimes you’re trying to find something more — something which will act because of the total command center for your smart home. If that sounds more your speed, inspect our list of the best universal remotes.

Avera Universal Remote Codes and Program Instructions

For avera tv also we’ve universal remote if you have already got the avera universal remote then check out the below list and obtain the avera universal remote code for your favorite device. After getting the code from the below list you’ve got to enter the code in your remote to program your avera tv.

Avera TV Universal Remote Codes List

Avera Universal Remote 3 Digit Codes

840
929
174
046
000
021

Avera Universal Remote 4 Digit Codes

0174
0151
1317
1361
1100
0046
1174
0019
5279
1091
1126

Avera Universal Remote 5 Digit Codes

10046
11508

GE Universal Remote Code For Avera TV

174
0174
5279
0151
Comcast: 10030
AT&T (U-verse): 1043
DirecTV: 10030
RCA Universal remotes: 0030
Dish Network Remote Controls: 506

1) Keywords

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Avera Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat an equivalent procedure with the various code from an equivalent a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll found out your universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some overtime but it’s vital to search out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the ultimate method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • You have to repeat for all the buttons to program, once you’ve got done all the functions which you would like and eventually press the “Setup Button” Again to end the session.

Conclusion:

This is the simplest blog to urge all kinds of Avera Universal Remote Codes, just you would like to see your device name then get the code either it’d be a four-digit or five-digit universal remote code then your remote has been found out to your device. Now you’ll operate easily.

Hitachi TV Universal Remote Codes and Program Instructions

Get the universal remote codes list for your favorite Hitachi brands like DVDs, amplifiers and receivers…etc regardless of the brand you utilize which has come from the Hitachi family just check your device name within the below list and obtain the universal remote codes.

Hitachi Tv 4 Digit Universal Remote Codes List

TV 4 Digit Codes
1004
1009
1010
1013
1053
1057
1058
1065
1078
1083
1113
1114
1115
1128
1173
1004
1011
1012
1051
1052
1084
1086
1087
1102
1225
1384

Hitachi DVD Universal Codes List

Hitachi DVD Codes
2000
2027
2126
2173
2240
Hitachi Amplifier Codes
6034
Hitachi HDTV Codes
1030
1132
1133
1134
1191
1208
1209
1210
1211
1212
1226
Hitachi VCR Codes
3052
3055
3117
3169
Hitachi Receiver Tuner Codes
5159

1) Keycode

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Hitachi Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat a similar procedure with the various code from a similar a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll set up your universal remote to look mode for the proper one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some additional time but it’s important to search out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the final method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” which means it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • You have to repeat for all the buttons to program, once you’ve got done all the functions which you would like and eventually press the “Setup Button” Again to end the session.

Conclusion:

We have mentioned all the remote codes for this Hitachi brand, we also mentioned the steps to program your device with the universal remote. to induce the code for your device to continue your universal remote then operate your favorite channel.

Pavy Universal Remote Codes and Program Instructions

Pavy Universal remote various codes for various devices like insignia, Vizio, element tv…etc now we are getting to mention those universal remote codes and you’ll collect them within the below table. If you don’t skills to program your pavy universal remote for your device then you would like to do the below methods then you’ll easily operate your device.

Pavy Universal Remote Codes List

BrandCodes
Admiral500, 501, 610, 614, 615,902
Advent911, 932, 933
Aiko900
Akai601
AOC103, 601, 617
Apex000, 604, 618
Audiovox100, 101, 900, 901
Belcor617
Bell&Howell611, 620
Bradford901
Brockwood617
Broksonic614, 902
Candle601, 619
Celebrity605
Changhong618
Citizen601, 619, 900, 903
Clairtone103
Concerto619
Contec103, 901
Craig901
Crosley301, 303
Crown901
Curtis Mathes100, 102, 301, 400, 401, 402, 405, 500, 603, 606, 611, 619, 620, 621, 903
CXC901
Daewoo100, 101, 617, 900
Daytron617
Dumont617, 700
Durabrand201, 614, 615, 914, 918
Electroband103, 605
Emerson101, 103, 200, 201, 620, 901, 902
Envision601
ESA201, 601, 901, 903
Fisher620, 801
Fujitsu300, 615
Funai201, 615, 901
Futuretec901
GE100, 200, 202, 400, 401, 402, 405, 607, 608, 802
Gibralter601, 617, 700
Goldstar601, 607, 617, 619
Grundy615, 901
Haier914, 918
Hallmark607
Harvard901
Hitachi005, 606, 611, 916, 619
ILO921, 925
Infinity301
Inteq700
Insignia201, 301, 303, 614, 909, 919, 920, 934
JBL000, 301, 604, 618
JCB605
JC Penny202, 400, 402, 405, 601, 607, 608, 609, 617, 800, 903
JVC701
KEC901
Kenwood601, 617
KLH618
KTV103, 601, 901
Konka001, 002, 003, 304, 904
LG619, 700, 910
Logik611
Luxman619
LXI301, 400, 402, 607, 609, 620
Magnavox301, 302, 303, 601, 615, 617, 803, 905, 906, 907, 908, 909
Majestic611
Marantz301, 601
Matsushita004,
Megatron606, 607
MEI103
Memorex004, 104, 607, 611, 614, 615, 620
MGA104, 500, 601, 607, 617
Minutz608
Mitsubishi104, 500, 601, 607, 617
Motorola500, 802
MTC103, 601, 617, 619, 903
Multitech901
NAD603, 607, 609
NEC601, 617, 619
Nikko601, 607, 900
Noshi800
NTC900
Olevia923
Onwa901
Optimus004, 603, 620
Optonica500, 610
Orion614, 615, 902
Panasonic004, 202, 610, 802
Philips301, 601, 617, 803, 905, 906, 907, 908, 909
Philco301, 601, 606, 614, 617
Pilot601, 617
Pioneer600, 603
Polaroid400, 910, 913, 915, 917, 920
Portland617, 900
Prism202
Proscan400, 402
Proton102, 607
Pulsar617, 700
Quasar004, 202, 610, 802
RadioShack400, 402, 607, 610, 617, 619, 620, 621, 901
Rhapsody103
Roomconx614, 615, 902, 924
Runco601, 616, 700
Sampo601
Samsung601, 607, 617, 619, 903, 930
Sansui614, 615, 902
Sanyo620, 801, 931
Scotch607
Scott607, 615, 617, 901, 902
Sears201, 301, 400, 402, 607, 609, 615, 620, 622, 801
Sharp500, 501, 610, 929
Sharp (LCD)500, 501, 610, 929
Shogun617
Signature611
Simpson803
Sony605
Soundesign607, 615, 901
Squareview201
SSS617, 901
Starlite901
Supreme605
Sylvaina201, 301, 601, 901
Symphonic201, 901
Tandy500
Tatung802
Technics004, 202
Techwood202, 619
Teknika104, 301, 605, 611, 615, 617, 619, 900, 901
TMK602, 607, 619
Toshiba609, 613, 620, 903
Trutech101
Victor701
Vidtech607, 617
Vizio927
Wards301, 601, 607, 608, 610, 611, 615, 617, 619
Westinghouse926, 928
White Westinghouse101, 605, 614
Yamaha601, 617
Zenith611, 614, 619, 700, 900

1) Keycode

By using the keycode we will easily program a universal remote and also the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Pavy Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat a similar procedure with the various code from a similar a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that point you’ll set up your universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some additional time but it’s vital to search out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the ultimate method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To The Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” for example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” meaning it’s been saved correctly
  • Now your “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • You have to repeat for all the buttons to program, once you’ve got done all the functions which you would like and at last press the “Setup Button” Again to end the session.

 

We hope you’ve got found out your pavy universal remote for your device. If you couldn’t operate this remote then try and created the pavy universal remote with other codes then the remote are working smoothly without giving any sorts of interruptions.

Huayu Universal Remote Codes and Program Instructions

We have three methods to setup huayu universal remote on our favorite device, you’ll use any of them which is suitable for your device. This one among the best universal remotes, so we recommend you utilize this remote.

Huayu Universal Remote Codes List

  • 011, 017, 029, 032, 034, 054, 067, 069, 071, 075, 076, 077, 078, 079, 080, 081, 107, 113, 117.

Try these codes also

  • 0028, 0026, 0022.

1) Keycode

By using the keycode we will easily program a universal remote and therefore the keycode identifies the make and model of your equipment.

  • First, you would like to “Turn The Device On
  • Press the “TV” on your “Huayu Universal Remote
  • Now press and hold the “Setup button” of the Universal Remote until it shows the “Light Flash” (It means it’s in “Learning mode”)
  • Finally, enter the “Keycode” which you collected from the programming guide (Instructions Booklet)
  • Once you’ve done this procedure, just “point your remote at the TV” then “Press And Hold The Power” button
  • You can release the “Power Button” whenever the screen switches off

That’s all, your TV will work perfectly now with the universal remote if your device isn’t working then attempt to repeat a similar procedure with the various code from a similar a part of the reference table.

2) Programming Via Universal Remote Code Search

If you couldn’t find the key code which works for the device at that time you’ll found out your universal remote to look mode for the right one. Its a code within the manual which forces the remote into the search mode

  • First of all “Turn The Device On
  • Now press and hold the “Setup” button
  • Enter the “9-9-1” (three-digit) code
  • Now hold down the “Power Button” on the remote then press the Channel up them until the device during this case your tv “Turns Off

The above method might take some additional time but it’s vital to search out your key code. Once you’ve got done the above procedure your remote should be working for all the functions.

3) Manual Setup

If the above two methods can’t be helped to you then the final method is “Manual Setup”, if you configure the universal remote manually your device can work perfectly.

  • Place the “Remote Control facing To the Universal remote you would like to replace
  • Now press the “Setup Button” or “Magic
  • Then enter the “Code” (You can find this in Instruction Booklet) for manual Programming
  • Now press any of the function which you would like to “program” as an example “TV Volume Up
  • Then press And hold the corresponding key on the “Original Remote Controller
  • Finally, one among the lights will “blink” which means it’s been saved correctly
  • Now you’re “TV Volume Up” button has been saved to the Universal remote and you’ll use the quantity button.
  • You have to repeat for all the buttons to program, once you’ve got done all the functions which you would like and eventually press the “Setup Button” Again to end the session.

Now operate the huayu universal remote on your device by using the above universal remote codes. Check to check if the remote features a temporary memory that stores control information for some minutes once you need to change the batteries. Otherwise, you’ll need to reprogram the remote.